#27 First Attempt at Cheap HHO On Demand Water Heater

21 Comments

1. douglundy
   Posted January 27, 2012 at 10:50 pm | Permalink

   you clearly need lots more gas, a bigger generator or a holding system..Producer gas goes back to the prewar days. time to reinvent the wheel..

   Reply
2. 1981dasimpson
   Posted January 27, 2012 at 11:02 pm | Permalink

   if you pumped the water in the bucket heated to 72 back thru the pipe to be heated again you should get more heat

   Reply
3. fuelban
   Posted January 27, 2012 at 11:08 pm | Permalink

   Nice video, I too always start at the free, cheap end of a project, you learn so much more, Fluid dynamics, !, “Heat exchange” Flow rate, Your flow will in straight linier Pipe, move faster in the centre, and slower at the walls, Giving poor heat exchange from flame to fluid, what to consider is: to put a coil “In to” the pipe Like a helix coil, it forces wall clinging fluid into the central flow, & so carrying the heat too, it’s a cheap heat exchanger.( Fluid Mixer).
   Thom in Scotland.

   Reply
4. hydrogastech
   Posted January 27, 2012 at 11:14 pm | Permalink

   Should say kiln liner, not lion.

   Reply
5. hydrogastech
   Posted January 28, 2012 at 12:01 am | Permalink

   Some pretty crazy comments on here. Take a solid core steel rod about 10 in long, place ur torches on each end of rod. Spiral ur copper around the rod keeping closes, but not touching. Make tight twist so u get as many revolutions as possible. Use thick bailing wire to secure and keep copper from touching rod. Now wrap with a lion liner wool and watch the difference. You will be surprised. Good luck.

   Reply
6. Uneakdawg
   Posted January 28, 2012 at 12:35 am | Permalink

   @funnie1.com  Add lime juice and baking soda to your water to keep your cells cleaner and it produces higher amps and lower volts due to higher conductivity.

   Reply
7. heycolslaw
   Posted January 28, 2012 at 12:40 am | Permalink

   Check out Denny Kline’s conductivityTest and you will find the hho flame adjusts itself to the task . I suggest you try ceramic. Kudos!

   Reply
8. eloid777
   Posted January 28, 2012 at 1:21 am | Permalink

   have you tryed this burning salt water to make more hho
   youtube.com/watch?v=e8utkoK2DhA&feature=related

   Reply
9. eloid777
   Posted January 28, 2012 at 1:29 am | Permalink

   double wall will contain your water, the inner bucket will hold you all your hho torch equipment. make or buy a cheep sprinkle that rotates 360 degree, have the sprinkle retro fitted with hho torch heads, feed hho into it
   size the buckets size the for the sprinkler, note the double wall of water should be thin and insulated….your double wall container will have in and out port make, add 2-3 sprinkler to the container asneed for noe heet output. eloid was the fist to invent this concept!!!

   Reply
10. eloid777
    Posted January 28, 2012 at 1:38 am | Permalink

    why dont you make a double wall contain ie buck with a bucket, fill the inner

    Reply
11. DutchUnited71
    Posted January 28, 2012 at 2:32 am | Permalink

    Nice one man. Check this one
    HHO Epoch Oxy Hydrogen Generator Cooking 1

    Reply
12. hydroxmobile
    Posted January 28, 2012 at 3:16 am | Permalink

    Try to use ceramic to wrap around the copper tube. You will get better results!

    Reply
13. MrBlue609
    Posted January 28, 2012 at 3:48 am | Permalink

    wow good job man. My only suggestion would be to try a rocket stove mass heater design type. This may help hold heat. But I think thats what you were going for with your crimped copper tubing. How did that work? Did it increase your heat?

    Reply
14. hhoball
    Posted January 28, 2012 at 4:21 am | Permalink

    @overunitydotcom It was only fractionally better than the others. I have been working on tons of stuff and one of them is the next version of a water heater. When i finish that and make a video, i will include the results of that last one you saw.
    Lots to come!

    Reply
15. overunitydotcom
    Posted January 28, 2012 at 5:16 am | Permalink

    What came out of the last experiment, where you wrapped the copper
    wire around the copper tube ?
    Did it heat more ?
    Well done and good luck with your experiments.
    Regards, Stefan.

    Reply
16. hhoball
    Posted January 28, 2012 at 5:57 am | Permalink

    @dominicboisvert – There are some usefull parts on both but the problem is, the amount of holes which the gas comes out of. Too many holes causes flashbacks. Propaine holes are much smaller and better suited for HHO.
    Stay Safe.

    Reply
17. hhoball
    Posted January 28, 2012 at 6:08 am | Permalink

    @mphandel The holding tank version will be ready for video in about a month.
    I have other better ideas for ondemand water heaters which i am working on now. Over the summer i will have lots of usefull videos that combine solar and hydroxy.
    Stay Safe!

    Reply
18. dominicboisvert
    Posted January 28, 2012 at 6:18 am | Permalink

    can we convert a propane or a natural gas appliance and water heater to hho

    p.s very good videos thank.  step by step for a polution free energy

    Reply
19. mphandel
    Posted January 28, 2012 at 6:52 am | Permalink

    Do you have a vid on the holding tank version,,,,,I’d like to make one of those myself.
    And can that unit be idled somehow to heat the surounding home air on gravity basis?

    Reply
20. IST814
    Posted January 28, 2012 at 7:38 am | Permalink

    that is the coolest hho heater on demand i have ever seen !

    well done .. i did wonder if the stainless would work aswell

    IST

    Reply
21. MrHerrera30
    Posted January 28, 2012 at 8:16 am | Permalink

    oil holds heat better …. or you can use very salted water

    Reply